#Lutron homeworks interactive panel serial
#Lutron homeworks interactive panel software

Revision B - 26 February 2013 Lutron Home Control Remote Access FAQ Lutron Home Control Remote Access FAQ What software versions of RadioRA 2 / HomeWorks QS. Lutron HomeWorks QS helps home achieve NetZero rating. Dimming range of 100% down to 10% or lower with a minimum load of one fixture. 58 The Lutron Difference Table of Contents You can count on HomeWorks QS for energy savings without sacrifice.

Save Energy with nparalleled Total Home Control. HomeWorks QS Keypad Design & Style Ordering Guide Lutron Electronics Co., Inc., 7200 Suter Road, Coopersburg, PA 18036-1299. Youll always have a warm welcome home with HomeWorks QS. Lutron Electronics today announced the availability of new Lutron Connect packages as well as a family of DIN rail panels and modules, opening the door to more project opportunities for its. Temperature control from Lutron is available for RadioRA 2 and HomeWorks QS total home control systems. 3' LED ULTRA-SHALLOW FIXED DOWNLIGHT product.

#Lutron homeworks interactive panel serial

Homeworks QS - ELK-M1XSLC M1 Interface Kit for Lutron Homeworks QS (special firmware required) RadioRA 2 - ELK-M1XSLU M1 to Lutron RadioRA2 Serial Interface. from a Lutron Sivoia QS Wireless control. Simple and clear control of shades, draperies, and lights using Lutron. My main question is wiring for the new QS. I understand Lutron is coming out with (may already be available?) with a Homeworks QS system. For more information, see Load Type and Capacity.Lutron Homeworks Qs Range ->->-> /emndr Note: Load controls have load type and capacity limits.The processor counts as one device and four locations are reserved for hybrid repeaters. With repeater: Up to 100 devices (e.g., load controls, Pico wireless controls, Radio Powr Savr sensors, shades, and repeaters) are supported per RF link.Note: All outside wire diameters must be the same and must be between 5.2 mmвЂ“8.5 mm (0.2 inвЂ“0.3 in).HomeWorks in-line controls accept wire gauges between 0.5 mm2 to 2.5 mm2 (20 AWG to 14 AWG).The load control is not suitable for installation in places where it is fully enclosed in metal (e.g., metal enclosures, electrical cabinets) or within metal ceilings. For optimal RF performance, no metal or other electrically conductive material should be present within 120 mm (4.75 in) around the top and sides of the load control.Remove any insulation, heat generating equipment, or obstructions within 120 mm (4.75 in) of the load control. Allow adequate space to ensure convective cooling of load control.Power failure memory: should power be interrupted, the control will return to its previously set level prior to the interruption when power is restored.Tested to withstand surge voltages without damage or loss of operation, in accordance with IEEE C62.41-1991 Recommended Practice for Surge Voltages in Low-Voltage AC Power Circuits.Tested to withstand electrostatic discharge without damage or memory loss, in accordance with IEC 6.System devices operate on 868 MHz, 868 MHz Limited, 865 MHz or 434 MHz Limited frequencies. They must be located within 9 m (30 ft) of a hybrid repeater. HomeWorks in-line load controls communicate with the system through Radio Frequency (RF).Ambient operating temperature: 0 вЊ to 40 вЊ (32 вЏ to 104 вЏ), 0% to 90% humidity, non-condensing.Remote device association allows for in-line controls to be added to a system without physically accessing product.Small size allows for simple retrofit installation.Also, the load controls can be controlled from anywhere in the world. When used with a HomeWorks hybrid repeater*, the load controls can be programmed and controlled via lighting scenes, scheduled daily events, the Lutron Connect app, and other HomeWorks QS system features.The switch is rated for 6 AX of general purpose lighting load and 2 A/0.5 HP of motor load.The reverse-phase dimmer is trailing-edge capable of up to 250 W of incandescent/halogen/ELV loads and up to 1 A/150 W of LED.Using a HomeWorks hybrid repeater allows devices to be part of a whole house solution that can be controlled remotely from anywhere in the world. HomeWorks in-line load controls use Lutron patented Clear Connect RF technology which provides reliable, wireless communication with other HomeWorks devices. The HomeWorks family of in-line dimmers and switches can control lighting and motor loads and provide a system that is convenient and easy to install.